The ipcheck command is used to display the output of specific parameters from OmniPCX Enterprise configuration and to check the consistency for each parameter.
This tool is available for CPU8 and CS firmware.<\/p>\n\n\n\n
<\/p>\n\n\n\n
(604)node001004> ipcheck
Enter Valid Arguments
-H Display the usage
-all Check all
-l Check Licences
-link Check NW links & trunks
-sipe SIP Extension
-sipd SIP Device
-sip Check SIP parameters
-g all Check all gateways
-g # Check this gateway
-comp Check Connexion and Multicodec parameters
-crypt Check Encryption<\/p>\n\n\n\n
(604)node001004> ipcheck -all
——————License Check——————-
G729 Server :30\/30
SIP Users :2\/100
G729 Client :9\/100
SIP Virtual Links :0\/5
Standard IP users :7\/0
SIP Extension users :2\/100
SIP TLS comm simultaneous :0
VoIP channels on OMS :0
Native Encryption Users :1\/70<\/p>\n\n\n\n
——————–Check Network Links———————
+———-+————+—————+———+————–+
| Number | Name | Destination | State | Encryption |
+———-+————+—————+———+————–+
| 2002 | LOOP CCD | node 4 | UP | TRUE |
| 2004 | N4_N1 | node 1 | UP | FALSE |
+———-+————+—————+———+————–+
+———-+——————–+
| Nodes | Compression Type |
+———-+——————–+
| 1 — 4 | G711 |
| 1 — 99 | G711 |
| 4 — 99 | G711 |<\/p>\n\n\n\n
—————Check System parameters for Compression—————-<\/p>\n\n\n\n
—————Check compressor per IP domain—————
+———-+———–+——–+————+————+
| number | allowed | used | RIP Intr | RIP Extr |
+———-+———–+——–+————+————+
| 0 | ffff | 0 | G711 | G711 |
| 1 | ffff | 0 | G729 | G729 |
+———-+———–+——–+————+————+
————————–Check Compressor per coupler————————–
+——+——+———————+—————–+—————-+—————+
| cr | cp | type dsp | coupler state | H323 Gateway | RTP Proxies |
+——+——+———————+—————–+—————-+—————+
| 0 | 3 | INTIP3A ARMADA* | IN SERVICE | 30\/30 | 0\/0 |<\/p>\n\n\n\n
——— Check DPNSS prefix —————————————<\/p>\n\n\n\n
————————Check System parameters for SIP————————-<\/p>\n\n\n\n
—————————Check SIP Proxy parameters—————————
*SIP\/Proxy – Minimal authentication method :SIP NONE
ERROR!! The value should be DIGEST else malicious calls can occur.
Update the configuration of all SIP users with SIP password and
reactivate.
*SIP\/Proxy – Authentication realm :node004
*SIP\/Proxy – Only authenticated incoming calls :True
Retransmission number for INVITE :3
————————–SIP Trusted IP Address List—————————
Trusted IP Address 1:192.168.1.144
————————SIP Quarantined IP Address List————————-<\/p>\n\n\n\n
————————SIP GATEWAY————————-
Trunk Group :114
IP address :192.168.1.143
Machine name :node006004
Proxy Port Number :5060
Dynamic Payload type for DTMF :97<\/p>\n\n\n\n
============================================================
S I P E X T E R N A L G A T E W A Y 990
============================================================
Gateway Name :WebRTC GW4
State :IN SERVICE
Remote domain :192.168.1.144
Transport :UDP
Use trunk group number :990 (ISDN)
Gateway Type :Rainbow Type
SRTP :RTP only
Type of codec nego :SingleCodecG711
Re invite without SDP :TRUE
SDP in 180 messages :NO
incoming calls 100 REL :Not Requested
outbound calls 100 REL :Supported<\/p>\n\n\n\n
————————–List of SIP Extension Users—————————
+——–+———-+——————+————–+—————–+————
+———-+——————-+
| Neqt | Number | Name | IP address | Video Support | Sub Type |
Domain | MAC address |
+——–+———-+——————+————–+—————–+————
+———-+——————-+
| 03636 | 60010 | Test User 6001 | Unused | NO | NA |0 | 00:00:00:00:00:00 |
| 03638 | 61005 | 61005 SIP | Unused | NO | NA |0 | 00:00:00:00:00:00 |
+——–+———-+——————+————–+—————–+————<\/p>\n\n\n\n
———————List of SIP Device Users——————–
+————+———+—————————-+———-+
| MCDU | Index | URL | Ext.gw |
+————+———+—————————-+———-+
| 4036 | 0 | 4036@ pve-oxe1 | — |
+————+———+—————————-+———-+<\/p>\n\n\n\n
—————————-Configurations To Check—————————–
Reject unidentified proxy call: False
WARNING!! Must be True to force identification of inbound call
Minimal authentication method: SIP NONE
ERROR!! The value should be DIGEST else malicious calls can occur.
Update the configuration of all SIP users with SIP password and reactivate.<\/p>\n\n\n\n
————- List of recommended commands ——————————–<\/p>\n\n\n\n
(604)xb006004>
Chapter 2 Maintenance Commands<\/p>\n\n\n\n
The ipcheck command is used to display the output of specific parameters from OmniPCX Enterprise…<\/p>\n